Monster Bumper Rack
Monster Bumper Rack
Caratteristiche del prodotto | |
| Marca | Rogue Fitness |
| Colore | Nero |
| Prodotto negli Usa | SÌ |
| Peso del prodotto | 180LB |
| Lunghezza | 44" complessivi, piastre stabilizzatrici a pavimento incluse |
| Larghezza | 23,5" complessivi, piastre stabilizzatrici a pavimento incluse |
| Altezza | 24,375", 31,625" per approssimazione fino alla parte superiore dei divisori |
| Foot Print | 44" x 23,5" |
| Informazioni sull'acciaio | Acciaio calibro 11 da 3x3". Fori per accessori di montaggio da 1" |
| Altre specifiche del prodotto | Laser cut Rogue branding, MG Black powder coat finish |
Descrizione prodotto
The Monster Bumper Rack is a compact, customizable equipment storage unit, made in the USA from the same 3x3” 11-gauge steel as our Monster Power Racks and Rigs. The patented, 180 LB design includes an adjustable top rail and dividers for plates, with a flat, reinforced bottom shelf (40.5” wide x 20” deep) for other assorted gear.*
Leggi ancora
Monster Bumper Rack
Patented
The Monster Bumper Rack is a compact, customizable equipment storage unit, made in the USA from the same 3x3” 11-gauge steel as our Monster Power Racks and Rigs. The patented, 180 LB design includes an adjustable top rail and dividers for plates, with a flat, reinforced bottom shelf (40.5” wide x 20” deep) for other assorted gear.*
*The 40.5" wide x 20" deep bottom shelf is specifically designed to be large enough for storing two DC Lifting Block Sets, side by side.
Creating a total footprint of 44” x 23.5”, the Monster Bumper Rack also gives gym owners the ability to store and organize any size/type of plate as they please, simply by repositioning the (5) stainless steel dividers along the 1” spaced holes in the railway tubing. Each unit comes with all required 1” hardware for set-up, along with laser-cut Rogue branding, an MG Black powdercoat finish, and a set of foot plates with ½” diameter holes (should you wish to mount the rack to the floor).
Please Note: These units ship disassembled. A 1.5” wrench is required for set-up and is NOT included.
Caratteristiche del prodotto
Caratteristiche
- Prodotto negli Stati Uniti
- Patented Design
- 3x3” 11-gauge steel, holes for 1” hardware
- Unit Weight: 180 LBS
- Length: 44" overall, including footplates
- Width: 23.5" overall, including footplates
- Height: 24.375", 31.625" to approximate top of dividers
- Plate Storage Rail: 2x2” 11-gauge steel, 1” hole spacing
- Includes (5) Stainless Steel Plate Dividers
- Reinforced Bottom Shelf: 3/16” thick Laser-Cut Steel (40.5” x 20”)
- Medium Gloss Black Powdercoat finish
Spedizione
Spedizione veloce Rogue
Il Sistema di Spedizione Rogue ti consente di monitorare il tuo ordine dal momento in cui lo effettui fino al momento in cui arriva alla tua porta. Ordina oggi, traccia oggi.
KEY FEATURES OF THE MONSTER BUMPER RACK
Adjustable Plate Storage Rail
The parallel railway tubes at the top of the Monster Bumper Rack are made from 2x2” 11-gauge steel, and include holes with 1” spacing, creating endless ways to insert and line up the five included plate dividers; no hardware required. The dividers themselves are made of ½” solid round stainless steel, and measure 10.25” tall x approx. 7.613” at their widest point. They are equipped to safely bookend any size of standard plate, as the railway tubes are just 6” apart at their closest point.
Bottom Shelf - Heavyweight Storage
The bottom, flat shelf of the Monster Bumper Rack is made from 3/16” thick laser-cut and formed steel, with a 3x3” 11-gauge steel support tube underneath for extra reinforcement and structural integrity on heavier loads. The shelf measures 40.5” wide x 20” deep, and can be used for just about any type of small equipment, from KBs to medballs to a side-by-side set of DC Blocks.
Quality Rogue Construction - Made in the USA
All of our Monster Bumper Racks are manufactured in the USA, using the same 3x3” 11-gauge steel tubing and floor-mountable foot plates as our Monster Power Racks and Rigs. The unit is finished in an MG Black powdercoat, and the bottom shelf includes laser-cut Rogue branding. All 1” hardware required for assembly is included (customers will also need a 1.5” wrench for set-up, which is NOT included).
