GutscheineKontaktBestellstatus

Rogue RML-690 Power Rack 3.0

★★★★★
★★★★★
4.9
25 Rezensionen
Hergestellt in den USA.

Rogue RML-690 Power Rack 3.0

★★★★★
★★★★★
4.9
25 Rezensionen
Hergestellt in den USA.
Rogue RML-690 Power Rack 3.0
2.329,66 €
Versand in 4–6 Wochen

Farben (11)*Satin Black

Rack-Höhe*

Art der Senkrechtstrebe*

Rack-Tiefe*

Hardware Finish:

Front Pull-up Bar: (8)X-431 Single 1.25" Pull-up Bar

Rear Crossmember (3)Monster Lite 3.0 43" Nameplate Crossmember (+80,92 €)

J-Cup: (4)Monster Lite J-Cup Pair - Standard

Safeties: (3)43" Infinity/ML Pin & Pipe Safety System - Black Zinc (+85,68 €)

Plate Storage Pins: (5)4 Long / 4 Short - Black Zinc (+238,00 €)

Band Pegs: (3)None

Rogue RML-690 Power Rack 3.0 Zubehör
Verfügbare Optionen (2)

SAML-24 Monster Lite Safety Spotter Arms (Pair)
SAML-24 Monster Lite Safety Spotter Arms (Pair)Siehe Details
238,00 €
Concrete Anchor Kit
Concrete Anchor KitSiehe Details
32,13 €

Produktdaten

MarkeRogue Fitness
Hergestellt in den USAJa
Gewicht530LB
Länge76"
Breite49"
Höhe90.375"
Standfläche80" x 53"
Stahlinformationen11 gg starker Stahl mit 3 x 3" Kantenmaß, Bohrungen nach Westside-Muster
Weitere SpezifikationenInklusive 1 Holm mit 43" und 1 Single Skinny Pull-up Bar mit 43"
Produktbeschreibung

Das RML-690 Monster Lite Rack wurde ursprünglich entwickelt, um die robuste 3x3-Zoll- (11 des RM-6 Monster Racks mit der 5/8-Zoll Hardware des Infinity R-6 zu . Die neueste Version (3.0) hebt dieses Hybriddesign auf die nächste Stufe und bietet eine große Auswahl an individuellen Farbausführungen, ein verschraubtes Design für einfacheren Versand und Montage sowie mehr Vielseitigkeit.

Mehr lesen

Rogue RML-690 Power Rack 3.0

Das RML-690 Monster Lite Rack wurde ursprünglich entwickelt, um die robuste -Zoll-Stahlkonstruktion (11 Gauge des RM-6 Monster Racks mit der 5/8-Zoll-Hardware des R . Die neueste Version (3.0) hebt dieses Hybriddesign auf die nächste Ebene bietet eine große Auswahl an
Farbausführungen, ein verschraubtes Design für einfacheren Versand und Montage sowie mehr Vielseitigkeit.

KOMPAKTES DESIGN, MAXIMALE FUNKTIONALITÄT

Das in Columbus, Ohio, hergestellte RML-690 verfügt über 80" oder 90" hohe Pfosten mit lasergeschnittenem Westside-Lochabstand (1" durch die Bank und die Clean-Pull-Zone, 2" Abstand darüber und darunter). Das RML-690 ist in den Innentiefen 24", 30" und 43" sowie mit zusätzlichen Pfosten auf der Rückseite zur Lagerung von Gewichtsscheiben erhältlich und eignet sich für jeden Trainingsraum, von der Garage oder dem Heim-Fitnessstudio bis hin zu großen Trainingsanlagen.

ROGUE MONSTER LITE-SERIE

Das Ökosystem der Rogue Monster Lite Serie bietet zahlreiche Anpassungsmöglichkeiten, darunter J-Cups, Sicherheitsvorrichtungen, Kabelsysteme und Aufbewahrungsoptionen. Alle Anbauteile und Zubehörteile sind nahtlos in das RML
690 integriert, sodass Sie Ihr Rack flexibel an Ihre Trainingsbedürfnisse anpassen können.

LANGLEBIG

Das RML-690 zeichnet sich durch seine Langlebigkeit, Vielseitigkeit und sein kompaktes Design aus und ist damit eine zuverlässige Wahl sowohl für Heimstudios als auch für professionelle Einrichtungen. Ob als Herzstück einer Garage oder als dynamische Ergänzung einer Universitäts-, Profi- Militär-Trainingsanlage – dieses Rack ist auf Leistung und Langlebigkeit ausgelegt
Wie alle Rogue Racks
die lebenslange Garantie von Rogue.

Wichtig: Dieses Rack muss vor der Verwendung mit dem Boden verschraubt werden.

Hinweis: Die Satin Clear-Oberfläche ist transparent, d. alle Schönheitsfehler und Markierungen aus dem Herstellungsprozess sind im Stahl sichtbar. Edelstahlgestelle bestehen aus Rohstahlteilen und weisen leichte Unvollkommenheiten durch Laserschneiden und Schweißen .

Siehe auch: Weitere Racks der Rogue Monster Lite-Serie

Produktdaten

Spezifikationen

  • Hergestellt in den USA
  • Individuelle Rogue-Pulverbeschichtung in seidenmatter Farbe oder Struktur
  • Schwarze oder helle Zinkschrauben und -befestigungen (5/8 Zoll)
  • 3x3 Zoll 11-Gauge-Stahl – 80,375 Zoll oder 90,375 Zoll Höhe
  • Stellfläche: 61"-80" x 53"
  • Westside-Lochungsabstand – 1”-Abstände im Bank- und Umsetzbereich und 2”-Abstände darüber und darunter
  • Löcher oben/unten in den Querträgern für Slinger-Kompatibilität
  • Auswahl an Ständern mit oder ohne lasergeschnittener Nummerierung
  • Wichtig: Das Gerät muss am Boden verschraubt werden.

Hauptmerkmale des RML-690 Power Rack 3.0

Exclusive Custom Color Finish Options
1

Exklusive benutzerdefinierte Farbausführungsoptionen

Das Rogue RML-690 3.0 Rack ist in vielen seidenmatten Farben und strukturierten Pulverbeschichtungen erhältlich. Setzen Sie ein persönliches Statement oder gestalten Sie Ihr Power Rack in den Farben Ihres Teams, Ihrer Schule oder Ihres Unternehmens.

Quality Rogue Construction
2

ROGUE QUALITÄTSKONSTRUKTION

Der RML-690 verwendet hochbelastbare 3x3" Stahlpfosten der Stärke 11 mit 5/8" Durchmesser Schraubenbeschlägen der SAE-Klasse 5. Die lasergeschnittenen Löcher sind im klassischen Westside-Muster angeordnet, sodass in der Werkbank und im Zugbereich Löcher im Abstand von 1" und an den restlichen Pfosten im Abstand von 2" zum Anbringen Ihrer Anbaugeräte vorhanden sind. Bitte beachten: Die Einheit muss am Boden festgeschraubt werden. Bodenmontagezubehör ist nicht im Lieferumfang enthalten.

Monster Lite Ecosystem
3

Monster Lite-Ökosystem

Statten Sie Ihren Trainingsraum mit einer Stange, einer Bank, Gewichtsscheiben oder einer Reihe kompatibler Geräte und Zubehörteile, die speziell für die Rogue Monster Lite-Serie entwickelt wurden, komplett aus. Version 3.0 ist speziell für eine bessere Kompatibilität mit dem Latzug-Slinger-System konzipiert, da sich nun Löcher in der Ober- und Unterseite der Querträger befinden, durch die das Kabel ungehindert geführt werden kann.

Empfohlene Produkte

Rezensionen

Kommentar 1–8 von 25
Nathan C
Spanish Fort, AL
★★★★★
★★★★★
3 weeks ago
Awesome Piece of Equipment
My wife and I opted to get the Monster Lite 690 Rack setup and have no complaints. We wanted to buy once and cry once, and purchase a top-of-the-line product that could be trusted. We expect this to last quite a while. While it is expensive up front, it is more enjoyable to lift on a premium setup and will undoubtedly put us in a better health position going forward, which will save in the long run. The fit and finish were excellent, and not a single bolt was missing. I assembled this by myself. If you've ever worked with any type of tools or assembled furniture, etc., there is nothing to it...just take your time and follow the directions. Once you get the sides built (snugged up, but not fully tightened on the bolts), the only slightly dicey part was setting each side upright and balancing them (they'll stand up on their own) carefully avoiding bumping either side with the crossmember as it we being put into place. As mentioned, the fit and finish were superb, so I simply measured slightly more than the crossmember width of 43" and squared it up, leaving a slight gap so I could pop a bolt through on one side temporarily and the do the same on the other side, leaving a slight bit of play to not inadvertently knock down the other side with the crossmember while setting it. Then flip it up and square up the base and tighten it up. Once that is done, you're home free. I didn't time the setup, but would estimate it took roughly 6-7 hrs doing it solo start to finish, including unboxings and organizing parts. And my forearms were sore for 4-5 days afterwards from all the ratcheting. I opted for the biggest version to allow for the most room inside the cage. I also got 2 extra crossmembers/stabilizers, which I would recommend. It felt adequate the way it came, but once I attached the extra crossmembers this thing was rock solid with no need to bolt down. There's plenty of room for attachments. We added a dumbbell rack, matador, GHD, wall ball setup, and a landmine attachment for now and have plenty of variety as far as exercises that can be done utilizing just the rack portion alone, much less free weights outside of the cage. Lastly, I have to give a shoutout to R&L Carriers. They called and arranged the date of delivery and there was no timeslot crap. The guy said he'd be there at a certain time and that's when he showed up. He was courteous and had an electric pallet jack which was able to bring the entire oversized pallet from the road right up the driveway to my garage door, which save me from having to bring each box up the driveway.
Ja, ich empfehle dieses Produkt weiter
Ursprüngliche Quelle des Beitrags: roguefitness.com
Thunder_Junk
Las Vegas
★★★★★
★★★★★
Jun 2024
Best Power Rack I've ever used.
This has got to be the best power rack I've ever used.  The 690 model has plenty of walk-out room for squats.  I highly recommend buying this with numbers, eliminating guesswork when adjusting J-hooks or straps. It comes with 6 weight standards and UHMW padded j-hooks so you don't destroy your knurling on your barbells. 
Ja, ich empfehle dieses Produkt weiter
Ursprüngliche Quelle des Beitrags: roguefitness.com
Matty_L
★★★★★
★★★★★
Feb 2024
Unleashing Potential: ROGUE RML-690C Power Rack
From the moment I assembled the RML-690C in my garage gym, I knew my workouts were about to hit a new level of intensity. This beast isn’t just a piece of equipment; it’s a cornerstone for anyone serious about lifting. Build Quality and Design: Robust doesn’t even begin to describe it. The RML-690C’s American-made steel construction exudes durability and stability, no matter how heavy I go. Its custom color finish isn’t just about looks; it’s about making a statement. Functionality: Versatility is the name of the game. With a pull-up bar, safety straps, and ample plate storage, it’s like having a professional gym at home. Adjustability is a breeze, making it perfect for squats, bench presses, and everything in between. Experience: Each session feels safer and more efficient. The rack’s stability gives me the confidence to push my limits, and the setup options keep my workouts diverse and challenging. Final Thoughts: The ROGUE RML-690C Power Rack 3.0 is more than an investment in your fitness journey; it’s a commitment to excellence. Whether you’re a seasoned lifter or just starting, this rack will elevate your home gym experience. The only thing I wish I had was an additional stabilizer kit to add to the bottom rear of the machine, I added one to the top.
Ja, ich empfehle dieses Produkt weiter
Ursprüngliche Quelle des Beitrags: roguefitness.com
Mike D10
NEWBURY PARK, CA
★★★★★
★★★★★
Feb 2024
More than enough!
Unbelievably stout and tough squat rack. I ordered the forward addition for plate storage, but it may not be necessary depending on your setup. There is more than enough room on the rack, itself, to secure the plate holders (if they can be bought separately). The rack is sturdy enough to not need the front addition for stability and tip prevention--which was another concern of mine. ***Pay attention to the height, as I barely got this in my garage below an exposed footer that runs the width of the space. 100% satisfied with the rack. Rogue wins again!
Ja, ich empfehle dieses Produkt weiter
Ursprüngliche Quelle des Beitrags: roguefitness.com
Old Guy 40s
Minneapolis
★★★★★
★★★★★
Jan 2024
New/used Rack
I just picked up a used RML-690c rack and it’s very impressive. It was easy to re-assemble without directions.
Ja, ich empfehle dieses Produkt weiter
Ursprüngliche Quelle des Beitrags: roguefitness.com
Ed Q
Aurora, IL
★★★★★
★★★★★
Oct 2023
Rock solid rack
Just added this to the garage gym, and it it the perfect center-piece to the gym.
Ja, ich empfehle dieses Produkt weiter
Ursprüngliche Quelle des Beitrags: roguefitness.com
Remko_Hermans
Netherlands
★★★★★
★★★★★
Feb 2023
Still waiting for the nuts and washers
I ordered the rig about two months ago. But a with to little bolts and no washers and nuts. I contacten Rogue, and they have send over the bolts but no nuts and washers. I've asked for this again but havn't got a reply jet. So we couldn't proparly use the rig jet.
Hat dir der Kommentar geholfen?
Ja · 49
Nein · 0

Antwort von Rogue Fitness:

Feb 2023
We're very sorry to hear your Rack arrived missing some hardware. Our team is gathering these pieces now and getting them to you ASAP.
Stateoforange
Corvallis, Oregon
★★★★★
★★★★★
Jan 2022
The Best out there
This Rogue Rack is bulletproof and built to last a lifetime. I have customized mine a bit and I’m super happy with it. My son and I are grateful to have it.
Ja, ich empfehle dieses Produkt weiter
Ursprüngliche Quelle des Beitrags: roguefitness.com
#RYOUROGUEMarkiere deine Fotos auf Instagram und Twitter mit #RYOUROGUE, damit sie in unserer Galerie gezeigt werden könnenVollständige Galerie anzeigen