Just added this to the garage gym, and it it the perfect center-piece to the gym.

This Rogue Rack is bulletproof and built to last a lifetime. I have customized mine a bit and I’m super happy with it. My son and I are grateful to have it.

(see bottom for some SOLO construction tips) Ok so I just got done putting this thing together. In some ways its too early to review, but I already have some initial impressions. I shopped online for over a year before deciding to go big and get this rack and the adjustable bench. Amazon is full of good looking but low quality foreign racks. If you take the time, you can see all the defects in those products. I wanted to go local, so looked at several recommended US brands. I couldn't decides, so at the end of the day I decided to go with the slightly overpriced Rogue because I wanted the guarantees and quality that goes with it. These racks are amazing solid well-thought out constructions. The only defects were that some of the feet were slightly bent upon arrival. I decided to not worry about that, but if you are pushing huge weights around, you might want to talk to Rogue about this issue. One thing I regret ordering is the pin safety. It is terribad. It is OK if you are going to leave it in place, but adjusting its height is a pain in the butt. I imediatley ordered the safety strap system so I can have more flexibility. I am not going to anchor this thing, as it is a beast. But if you are throwing around more than 500 pounds, you should start thinking about anchoring for safety. ****I had to put this together fully solo. Difficult, but do-able. Follow instructions to put together each set of 3 side posts to make the "walls". Then lift these up and move into place. On concrete, they stood unsuported for me, but you might need to set up a temporary support. Now first place the pull-up bar by standing on a chair and VERY carefully putting it into place and hand-threading bolts. Loosely hand tighten all four bolts. Now the CRUX: The center Rogue top bar is a heavy beast, and will scratch your posts if you are not perfect. The way to install this is to (1) Get 2 bolts and 2 nuts, (2) turn Rogue top bar upside down then lift it to line up the bottom holes, (3) place both bolts backwards (inside to outside), (4) let go and put nuts on bolts, (5) ROTATE the entire Rogue top bar up 180 degrees so it is where it belongs, (5) secure top bolts as per instructions, (6) remove temporary bottom bolts and reinstall per instructions. Tighten all bolts on Rogue top bar and pullup bar.****

By far the best investment I have made into my garage gym. Wish it didn't have to come with the pin & pipe safeties, but we use this every day no matter what. Its a Rogue so I will be able to pass it down to my grandkids in 40+ years too which is a plus.

It does the job very well. It is very sturdy and I have never worried about it tipping over and I haven’t noticed it moving.

I upgraded to this rack (from a *cough*powertech*cough*) about a year ago and don’t regret it one bit. Benching - the WSBB spacing is great for getting the j-cups right where they need to be for benching. The pin and pipe safeties work just fine. Squating- no complaints on the hole heights. I’ve bailed 405 with the strap safeties and boy can I tell you, this rack is bomb proof. DL - I use the rack for pin pulls with bands. Even with the heaviest bands the rack doesn’t budge. I was a little concerned about that since I do not have it bolted down. What else can I say? The machining on the rack is great. Zero slag or burrs in the holes. Best investment I’ve made for my home gym hands down. I did have to buy my UPS driver a case of beer...

Its real good. Show stopper. Only problem is the pain scratching with metal on metal... can't really stop that though

Significant issues with shipping finally behind me, I am very much enjoying the new equipment. I’ve gone from working out at the local gym one or two days a week to working out six days a week. I will be back for more!